Copyright © 2020-2021 Shenzhen CDTech Electronics LTD. All rights reserved. Site Map Powered by iwonder.cn
A display programme that sells into four countries rarely has one supply problem. It has four customs regimes, four service expectations and a demand pattern that moves between them. Shipping a finished module from one plant is the simplest structure, but it carries the full value across every border and freezes the configuration at the factory gate.
Kitting and local assembly offer a different split: keep panels and components in the region, assemble or configure close to demand, and accept a second manufacturing step that has to be qualified and controlled. This guide sets out what changes, what it costs and where the control boundary has to sit.
Where the last assembly step happens.
A finished module moves the whole bill of materials across the border at once; kitting splits it, so panel, touch and backlight can be held and configured close to demand.
In a finished-module structure the buyer qualifies one part number at one site. Traceability, warranty and change control all point to that site, and the customs entry covers the complete product. The cost of that simplicity is that every variant is built before it ships, the duty base includes the full assembly value, and a mix change travels through the whole pipeline.
Kitting moves the last step into the region. Panels, touch panels, backlights, bezels, flex assemblies and firmware images are stocked and combined to order. That changes five things at once: where inventory sits, what value enters the border, how many part numbers the buyer manages, which site owns the final process, and who carries warranty for a failure that appears after local assembly. That places the partner inside the quality agreement rather than beside it.
Not every step can travel. The decision is less about assembling a module than about which operations can be repeated reliably outside the original plant, by a partner the buyer can control.
| Step | Finished-module supply | Regional kitting | Control consequence |
|---|---|---|---|
| Panel to bezel or chassis | Done at the module factory | Moves to the region | New site, same drawing |
| Touch or cover glass bonding | Done at the module factory | Usually stays, unless the partner is equipped | Cleanroom and yield risk |
| Backlight assembly | Done at the module factory | Rarely moves | Optical matching and dust control |
| Firmware and parameter setting | Done at the module factory | Moves to the region | Version control and test coverage |
| Final test, label and packing | Done at the module factory | Moves to the region | Test limits and traceability |
The pattern is that mechanical integration, configuration, labelling and final test travel well, while optical bonding and backlight assembly usually do not. A partner that claims to do everything should be able to show the equipment, the environment and the yield data for each step it wants to take on, because the qualification rests on evidence rather than intent.
Local assembly changes the duty base, but it does not automatically reduce duty. What enters the country is a panel or a set of components, valued and classified as imported goods. What leaves the local step is a finished module with a different classification, a different value and possibly a different origin.
Three questions decide the outcome. First, how are the imported parts classified under the HS nomenclature maintained by the World Customs Organization, and how is the finished module classified? Second, does the local work meet the substantial transformation test that would change origin, or is it minor processing that leaves origin unchanged? Third, what is the customs value, including assists, royalties and the cost of tooling supplied free of charge?
Assembly can also change which preferential rates are available, because origin determines eligibility. EU Access2Markets is a practical reference for the import rules of a destination market, and Incoterms 2020 sets who bears each leg and each customs obligation. A duty model built on assumptions rather than a binding tariff decision is a budget risk, not a saving.
A qualified process is a set of controlled conditions, not a building. When the last step moves to a partner, the buyer's approval has to travel with the drawing, the bill of materials, the work instruction and the test limits. If those documents are not the same documents used at the original site, the qualification does not carry.
The practical boundary is defined by four things: the released process specification, the equipment and environment it assumes, the acceptance tests with their limits, and the change-control route. A partner outside that boundary becomes an uncontrolled source, even if the panels are genuine and the assembly looks correct. ISO management system certification, described through the ISO standards portal, gives evidence that a system exists; it does not by itself approve the process.
Acceptance criteria should be written against a workmanship standard both sides recognise, such as IPC requirements for the assembly class involved. CDTech's quality and environmental documentation shows the kind of evidence a module supplier can provide to support that boundary. A process audit should follow the work rather than the certificate: watch a unit being built, then compare what happened with the released instruction.
Regional stock exists to cover the gap between a service promise and the time it takes to replenish. That gap has a shape, and the shape determines how much inventory is needed.
The calculation is straightforward once the inputs are agreed. Demand during the replenishment window sets the base, and variability sets the buffer. The buffer scales with the square root of the lead time, which is why cutting replenishment time is often cheaper than adding stock.
The z value comes from the target service level: about 1.28 for 90 percent, 1.65 for 95 percent and 2.33 for 99 percent, assuming normally distributed demand. Review the output against forecast error, product life and holding cost, and remember that stock cannot cover an allocation problem at the panel source. CDTech's custom sourcing guide sets out how replenishment terms fit into the wider sourcing file.
The comparison is often framed as freight against warehouse cost, which hides the more important term: the cost of carrying inventory for the weeks that air freight saves. Air freight buys time, and time has a price per week per unit.
A break-even helps. Divide the air premium per unit by the weekly carrying cost per unit, and the result is the number of weeks of cover at which holding stock costs the same as shipping by air. If the programme needs more cover, stock is cheaper. If it needs less, air freight usually wins, especially with spiky demand or a short product life.
The calculation changes when variants multiply. Stock has to be held per variant, while air freight can be used selectively for the variant that runs short. It also changes with duty and tax treatment of inventory, insurance and obsolescence. It changes again when the stock is held as panels rather than finished modules, because panels serve several finished configurations. That flexibility is the strongest argument for kitting in a programme with a wide mix.
A kitting agreement is a manufacturing agreement with a logistics wrapper. It should name the processes, the acceptance criteria and the evidence the partner must keep, not just volumes and price.
Two governance habits make the clauses work. The first is a joint review of yield and returns at a fixed cadence, using the partner's data rather than a summary. The second is a rule that any process change is notified before it runs, with samples available for approval. Without those, the agreement describes an intention rather than a control.
The structure should follow the demand pattern and the customs map, not the org chart. A useful sequence starts with the markets, not the suppliers: list the countries, the duty treatment of panels and finished modules, and the service level each customer actually needs. Then quantify demand variability and the number of variants per market.
With those inputs, the choice usually becomes visible. A programme with stable demand, few variants and long product life can justify regional stock of finished modules. A programme with many variants and moderate volume usually benefits from holding panels and kitting locally, because one panel can serve several finished products. A programme with spiky demand and a short life is often better served by air freight from a central plant and a small safety buffer. Whatever the choice, the first market should run as a pilot that produces the evidence for the next one.
If your team is choosing between finished modules, regional stock and local kitting, send the market list, the variant count and the service level you have promised. CDTech can respond with the panel options, the documentation a local partner would need and an outline of what has to be qualified.
What does kitting change in the supply chain?
It moves the last assembly and configuration step from the module factory to a partner in the destination region. Panels, touch panels, backlights and firmware are held locally and combined to order. That changes where inventory sits, what value crosses the border, how many part numbers the buyer manages and which site owns the final process. It also adds a manufacturing site that has to be qualified and audited like any other.
Does local assembly reduce duty?
Not automatically. Local assembly changes the duty base, because the imported panel or components are valued and classified as they enter, and the finished module leaves under a different classification. Duty falls only if the tariff difference and the origin rules work in that direction. Minor processing may not change origin at all. Model the classification, valuation and origin questions, and confirm them with a customs adviser before counting a saving.
How is quality controlled at a local assembler?
The same way it is controlled at any manufacturing site: a released process specification, approved equipment and environment, defined acceptance tests, traceability and change control. The buyer's approval has to travel with the drawing and the bill of materials. Add incoming inspection of panels, first-article approval, lot acceptance testing and audit rights. A partner that cannot show these records is outside the qualification boundary, however good the samples look.
When is regional stock cheaper than air freight?
When the cost of holding a unit for the weeks that air freight would save is lower than the air premium on that unit. Divide the premium by the weekly carrying cost to find the break-even cover. Stock also has to be held per variant, while air freight can be used only for the variant that runs short. Stable demand, few variants and a long product life favour stock; spiky demand and a short life favour air.
By continuing to use the site you agree to our privacy policy Terms and Conditions.